Resin Coasters: How to Pour, Pop Bubbles and Use the Lighter Trick

Hi friends! I made a set of silver-sprinkle resin coasters, and I filmed the whole pour so you can see exactly how it goes — including the part where I run short on resin mid-pour and the little lighter trick that pops the bubbles. Nothing fancy, just how I actually do it at the craft table.

What you need to make resin coasters

Here are the supplies from the video, or similar ones if you want to try it yourself.

As an Amazon Associate I earn from qualifying purchases. Using these links doesn’t cost you anything extra — I just earn a small commission when you buy through them.

How to pour resin coasters, step by step

1. Measure and mix the resin

Start by measuring out equal parts of epoxy resin — part A and part B. Stir slow and steady. If you whip it fast you will fold a whole bunch of air into it, and that air becomes bubbles later. Slow stirring is the first way you keep bubbles down.

2. Get the bubbles out before you pour

Before the resin goes into the mold, let it sit a minute so some of the bubbles rise on their own. Then pour slow. Here is the trick that works for me: let a little popsicle stick hold the bubbles back while you pour. The stick catches the bubbles at the surface so they do not go into the mold with the resin. That is how I did these silver-sprinkle coasters, and you can see it in the video.

3. Pour the coasters and add the glitter

Pour the resin into the silicone molds, then sprinkle in the silver glitter. The glitter settles through the resin and gives the coasters that sparkle. Do not overfill the molds — leave a little room so the resin does not spill over the edge when it settles.

4. What to do when you run short on resin

I miscounted and ran short on resin mid-pour. It happens! Do not panic and do not try to stretch what is left. Just mix up another batch — I mixed another four ounces — and keep going. The new resin blends right in with what is already in the mold, and once it cures you cannot tell where one batch ended and the next began.

5. The lighter trick

This is my favorite part. Once the coasters are poured, take a refillable butane torch and pass it quickly over the surface of the resin. The heat pops the bubbles sitting on top — you can watch them disappear. Keep the torch moving and do not hold it in one spot. A quick pass is all it takes. You can see it happen in the video, right around the 19-minute mark.

6. Cure and finish

Once the bubbles are gone, the coasters go into the curing machine. When they are fully set, pop them out of the silicone molds and they are ready to use. If an edge is a little rough, a quick wipe with an alcohol wipe cleans it up.

Tips for fewer bubbles in resin

  • Stir slow. Fast stirring whips air in. Slow, steady stirring keeps it out.
  • Pour slow. A slow pour lets bubbles escape instead of trapping them.
  • Use the popsicle stick. Hold the bubbles back at the surface while you pour.
  • Warm the resin slightly. Room-temperature resin flows better and releases bubbles more easily than cold resin.
  • Use the torch. A quick pass with a butane torch pops surface bubbles after the pour.

Common resin coaster questions

Why do I get bubbles in my resin?

Bubbles come from stirring too fast, pouring too fast, or from air trapped in the mold. Stir slow, pour slow, and use the lighter trick after the pour to pop the ones that are left.

What happens if I run out of resin mid-pour?

Just mix more and keep going. Mix up another small batch and pour it in — it blends with what is already there and cures as one piece.

How long do resin coasters take to cure?

It depends on your resin and your curing setup. I use a curing machine, which speeds it up. Check your resin’s instructions for the full cure time, and do not pop the coasters out of the mold until they are fully set.

Come craft with us

Join us for project nights, Tuesday and Thursday 6–8pm at the Crafting with Donna store in Backus, MN. You can prepay for a project night here: https://craftingwithdonna.square.site/

More from Crafting With Donna: https://craftingwithdonna.com

From the craft table of Donna — crafter and owner of the Crafting With Donna store in Backus, MN

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *